Review Artisan Cutlery Revel

  

-  another Laconico design

It would be an exaggeration to say that I collect knives designed by Ray Laconico, but it so happens that I have a couple of them at the moment, of which this one from Artisan Cutlery, called Revel, is the latest!

I have also reviewed another model from Artisan's sister brand, CJRB, called Prado, which is also designed by the same person.

Artisan Cutlery Revel

Like many models from Artisan Cutlery, this one is also available in several different versions. In this configuration, the Revel comes with a metal handle and a slightly simpler steel, but it can also be had with an FRN handle with the same steel or a really nice S90V. The FRN versions are button locks and are also available in different colours and with or without black-coated blades.

Depending on budget and needs, there are different options to choose from.

Then, Revel has also been made in a couple of extremely luxurious editions featuring titanium handles and S90V or Magnacut. But they have been sold out for some time now.

Revel is another stylish knife signed by Ray Laconico

Short version: Artisan Cutlery Revel, A stylish and elegant knife that is both easy to carry and practical as an EDC knife

Blade

The blade is a quintessential Clip point, which in this case has proportions that make it reminiscent of a typical Bowie knife. Although in a smaller and folding version. Smaller in this case is still relatively substantial for a folding knife with a length of 90 mm. This should be put in relation to a height of 32 mm at most. The blade material is 3.2 mm thick.

The most distinctive feature of this knife is the distinctive clip-point blade.

The finish is a glossy satin, and the marking consists of the Artisan Cutlery logo on one side of the ricasso and on the opposite side, you will find the serial number and steel type. The Laconico name is also found on the blade. However, everything is sympathetically discreet and does not destroy the clean lines of the blade.

They are also reinforced by a pronounced false edge and a high sabre grind. The latter measures just over two centimetres in height. This causes the blade to narrow to about 0.6 mm behind the edge. A figure that, in my opinion, is too much for a folding knife and more suited to a large cleaver. Here, Artisan Cutlery could well rely more on the material and thin out the blades.

The blade is also distinguished by the fact that the beginning of the spine tends upwards and forms a thumb ramp with grooves for better grip. Then the blade hole is, of course, something that is obvious.

The steel used is AC's own AR-RPM9 steel, a steel that has proven to be viable. It is a typical all-round steel in the mid-segment, where you also find competitors such as 14C28N and N690. Not at all fussy, actually. It holds its sharpness fairly well and resists corrosion well. It is also very easy to sharpen, which is always nice.

The steel used is Artisan Cutlery's own AR-RPM9

As soon as you start using the Revel, you realise that this is a practical knife. A clip point blade is often good for many things, and that applies here as well. For more common EDC tasks such as cutting plastic straps, tape, rope and thinner string, cutting nylon straps around packages, etc., this blade works very well. In addition, there is something about the geometry that, despite the knife being thick behind the edge, makes it a veritable cardboard shredder.

The tip is also just as good as it looks. Sharp without being too flimsy. Then we come to the most positive surprise. Revel cuts very well in wood! That it does so in fresh branches may not be so strange. The factory edge gets approved; it is sharp and symmetrical. But that the knife would be so good for drier wood was surprising to me. The handle also helps by being long enough so that the little finger does not get an unpleasant amount of pressure when the knife wants to rotate in the hand when there is some force behind the cuts.

Even in lighter materials such as ordinary textiles, Revel is very workable. A lot of clothes are used for cleaning bicycles in a cyclist's household, and I make them out of worn-out clothes. 

Handle

The handle on this version is, as previously stated, made of titanium. In this case, this means two solid pieces that are just over three millimetres thick. No attempts have been made to lighten them. They are flat on the inside, which, on the other hand, makes cleaning easier. A detail that is also made easier by the completely open back. There is also a bolt with a hole in it for a lanyard. In order for it to be used, a thinner string must be used. There is no space for, for example, a standard 550 paracord.

The knife is held together by two spacers in addition to the pivot screw. The screw heads are actually T8s but really bad if I'm being honest. The grip for a tool is almost non-existent with a domed screw head and a very shallow groove. Do not disassemble this knife! The risk of you standing there with round screw heads is almost one hundred per cent!

In this version, Revel has a titanium handle

The length of the entire handle is 115 mm, of which the available space for the fingers is about 93 mm. However, this does not feel cramped at all as the finger guard is softly shaped and you can place half your index finger over it without any problems. At the back, the handle widens slightly to prevent you from slipping backwards when cutting with the knife.

The knife is open at the back, and there is also a mount for a very thin lanyard.

The titanium sides are designed so that the pattern that is there gives the impression of panels. It gives a little grip, but it is mainly the shape and the depression for the index finger that help to keep the knife in the hand. There are also some grooves on the base of the blade spine for a thumb, but they are more of an indexing nature than giving any real grip. Something that I am happy about, as there has been more and more discussion recently about how such depressions in knife blades affect the general durability.

The finish overall gets approved as the edges and corners are sanded and rounded as they should be.

The Revel has a very comfortable handle. It's a little too thin to be extremely ergonomic.

In the hand, the Revel is comfortable in a relatively neutral way. It is not an ergonomic muscle package, but the index finger finds its place, and so does the rest of the hand. Then the relatively simple shape means that the two basic grips, sabre and hammer grip, work excellently.

The same can be said about reverse grips; nothing annoying there either. In general, the clip also stays out of the way despite being of the "deep ride" type. This is appreciated as they sometimes cause chafing due to their location far back on the handle.

Opening and Lock

This is an easy-to-open knife, provided you appreciate Spyderco's invention of the blade hole, of course. The alternative is to open the knife with two hands, which is, of course, possible.

The opening method is clearly visible from the hole in the blade

The blade hole is easy to access and comfortable to use as it is bevelled sympathetically. Much more and it would have become slippery. It is always a trade-off.

The fine ceramic ball bearings mean that this knife's blade has a tendency to fly out quickly. This is especially true if you use a so-called "Spydie flick" with your index finger on the back of the knife.

Then the blade is quite heavy, depending on the shape and thickness, so the detent can be overcome with a flick of the wrist for those who want to provoke their knife and open it that way.

A small disadvantage with the crispy opening and the heavy blade in combination is that the pivot screw has a tendency to unthread itself. You either have to adjust it at regular intervals or provide it with a little thread locking to keep it in place. After a while, otherwise the opening becomes too easy, and the blade starts to point away from the locking side. With a properly adjusted pivot, the blade is otherwise centred.

Here you will find a classic frame lock with associated lock bar reinforcement and overtravel stop 

The lock found on this knife is a frame lock with the usual accessories. This means a steel-reinforced lock bar and an overtravel stop. 

The function is very good with a lock that always engages and a lock bar that is easy to reach. The lock bar is also quite soft, which makes the lock easy to release. However, not so easy that it slips under incorrect load, i.e. pressure or light blows to the blade spine.

I also do not experience any play in the blade with the lock in place. However, this applies as long as the pivot screw has not unthreaded itself, of course.

To Carry

Revel is not too bad to carry in a pocket. With its 114 grams, as measured by me, it is not intimidating for its size. It is also just over eleven centimetres long, as mentioned above. This should be paired with a height of at most 35 mm and a thickness of only just over a centimetre.

Overall, a thin and light knife, especially if you compare it to the length of the available edge.

The clip is simple and of the spring steel type

The sides of the handle are flat, which also doesn't pose any obstacle when the knife is stored in a pocket. The pattern on the titanium does not affect how the knife feels when pulled or put away.

This is what Revel looks like in a pocket

The clip on the Revel is of the simplest kind, and here it is noticeable that this is actually a "hotter" version of a simpler model. That is, the titanium itself is an upgraded luxury detail.

Here you will find a spring steel clip directly picked from the manufacturer's shelf, and it is also found on other models. However, this does not mean that it is bad, just that it is nothing special and may look a little boring. A plus, however, is that its shiny polished finish is repeated in both screws and blades.

The function is good with some remarks. The ramp is small but generally does not pose a problem, although, as usual, I have comments on the tips pointing outwards. They can both chafe and feel sharp if you hit your hand on them. The springiness in the clip is good, and the space underneath, well, adequate, no more. Especially not as a couple of millimetres at the back edge is stolen by the fact that the clip is not recessed into the handle side. Another slightly cost-saving measure. Machining time is money.

To Conclude

Revel is another stylish and practical knife from Ray Laconico's pen or perhaps a CAD program. All the lines are as they should be, and what made me choose this knife was the stylish blade. It is shiny, nice and is a clip point that gives Bowie knife vibes. Just right in my opinion.

Then I like the purity of Laconico's design language in general. A few custom knives from him would not be unwelcome, but that is beyond my financial muscles. Instead, I have to rely on Artisan Cutlery, among others. In general, I have come to like their way of making knives in terms of production quality. Both fit and finish are usually good.

This is also the case, although with a few small exceptions.

Revel is a sympathetic EDC knife as it is both practical and easy to carry.

It's about a few small details, but they annoy me a little, I have to admit. One such thing is the quality of the screws. They are simply not good in this case. The screw heads are far too shallow. Enough said about that. Although the next detail is also about screws, it is the pivot screw itself. The problem with it unthreading itself is certainly quite easy to fix, but it assumes that you have Loc Tite or similar at home.

Then there was the grind. A sabre grind is what it is, but in this embodiment, I think it is far too thick behind the edge. What tasks should be performed with a folding knife that requires it to be 0.6 mm thick behind the edge? Now, it can also be fixed by grinding or rather, completely reprofiling the edge. It is too much work for me.

That said, the Revel doesn't cut badly, just not as well as I would like. But there is no risk of the edge chipping. It holds up well, and in combination with a comfortable handle.

Something that can also be discussed is whether or not there should be titanium on this specific model. On that point, Artisan Cutlery cater to different tastes, and I happened to choose this version. As I said, the model is available in other materials and more exclusive steels for those who prefer it.

Artisan Cutlery Revel is also sturdy enough to work in the woods if you feel like it

Overall, it can be concluded that the impressions of Revel are that this knife is a result of another successful collaboration between Artisan Cutlery and Ray Laconico. They have done it before, and I believe it will happen again.

Revel is both a stylish and not least easy-to-carry knife and is an excellent platform for those looking for a good EDC knife. Then, not least, the low weight combined with the fact that it cuts well in wood means that it is not unsuitable for outdoor activities either. There are options, and the simplest ones have a target price of $ 45, and this version ends up around $ 90.

Artisan Cutlery

Specifikations:

Length Overall 205 mm

Length Folded 115 mm

Weight: 114 g, weighed by me, stated 113 g

Blade Length: 90 mm

Blade Thickness: 3,2 mm

Blade Steel: AR-RPM9

Handle: Titanium

Lock: Frame Lock

Produced by Artisan Cutlery, made in China

/ J - positive

#knivesandbikes #aliaspostmortem #knivigtvarre 

Recension Artisan Cutlery Revel

 

-  ytterligare en Laconico-design

Det vore en överdrift att påstå att jag samlar på knivar designade av Ray Laconico men det har slumpat sig så att jag har ett par tre stycken vid det här laget varav den här från Artisan Cutlery kallad Revel, är den senaste!

Jag har även med goda vitsord recenserat en annan modell från Artisans systermärke CJRB kallad Prado som även den är formgiven aav samma person. 

Artisan Cutlery Revel

Likt många modeller från Artisan Cutlery finns även den här i flera olika utföranden. Dels finns Revel som här med metallhandtag och ett lite enklare stål men även med FRN handtag med samma stål eller ett riktigt fint S90V. FRN-versionerna är button locks och finns dessutom i olika färger och med eller utan svart finish på bladen. 

Så lite beroende på budget och behov finns det olika alternativ att välja emellan.

Sedan har Revel även gjorts i ett par extremt lyxiga utgåvor med titanhandtag och S90V respektive Magnacut i bladen. Men de är utsålda sedan en tid tillbaks. 

Revel är ännu en stilren kniv signerad Ray Laconico

Kortversion: Artisan Cutlery Revel, en snygg och elegant kniv som är både lättburen och praktisk som EDC-kniv

Blad

Bladet är en kvintessentiell clip point som i det här fallet har proportioner som får det att påminna om en typisk Bowie-kniv. Fast i mindre och fällbar utgåva då. Mindre i det här fallet är ändå relativt rejält för en fällkniv med en längd på 90 mm. Det skall ställas i relation till en höjd på 32 mm som mest. Bladgodset är 3,2 mm tjockt. 

Det mest utmärkande för den här kniven är det distinkta clip point-bladet

Finishen är en blank satin och märkningen består av Artisan Cutlerys logga på en sida av ricasson och på motstående sida hittas serienummer och ståltyp. På bladet hittas även Laconicos namn. Allt är dock sympatiskt diskret och förstör inte bladets rena linjer. 

De förstärks för övrigt av en uttalad falskegg och en hög sabelslipning. Den senare mäter strax över två centimeter i  höjd. Det får bladet att smalna av till ca 0,6 mm bakom eggen. En siffra som enligt mig är för mycket för en fällkniv och mer anpassat till en stor huggare. Här kan man gott från Artisan Cutlerys sida lita mer på materialet och tunna ut bladen. 

Bladet utmärks även av att början av ryggen strävar uppåt och bildar en tumramp som försetts med räfflor för bättre fäste. Sedan är bladhålet förstås något som är uppenbart. 

Stålet  som använts är ACs egna AR-RPM9-stål, ett stål som har visat sig gångbart. Det är ett typiskt allroundstål i mellansegmentet där man även hittar konkurrenter som 14C28N och N690. Inte pjåkigt alls faktiskt. Det håller skärpan tämligen väl och motstår korrosion bra. Det är också mycket lättslipat vilket alltid är sympatiskt. 

Stålet som använts är Artisan Cutlerys egna AR-RPM9

Så fort du börjar använda Revel inses att det här är en praktisk kniv. Ett clip point-blad är ofta bra till mycket och det gäller även här. Till vanligare EDC-sysslor som att kapa plastband, tejp, rep och tunnare snöre, skära av nylonband kring paket etc fungerar det här bladet mycket bra. Därtill kan det läggas att det är något med geometrin som trots att kniven är tjock bakom eggen gör den till en veritabel kartongstrimlare. 

Spetsen är därtill precis så bra som den ser ut. Vass utan att vara alltför klen. Sedan kommer vi till den mest positiva överraskningen. Revel skär mycket bra i trä! Att den gör det  i färska grenar kanske inte är så konstigt. Fabrikseggen får nämligen godkänt, den är vass och symmetrisk. Men att kniven skulle vara så pass bra till torrare virke var överraskande för mig. Handtaget hjälper också till genom att vara långt nog för att inte lillfingret skall få obehagligt mycket tryck på sig när knvien vill rotera i handen då man lägger lite kraft bakom snitten. 

Även i lättare material som vanliga textilier är Revel mycket gångbar. Det går åt många tygtrasor för rengöring av cyklar i en cyklists hushåll och de görs av gamla uttjänta kläder. 

Handtag

Handtaget på den är versionen är som tidigare sagts av titan. Det innebär i det här fallet två massiva stycken som är strax över tre millimeter tjocka. Några försök till att lätta dem har inte gjorts. De är flata på insidan vilket å andra sidan underlättar rengöring. En detalj som för övrigt även förenklas av den helt öppna ryggen. Där hittas även en bult  med ett hål i för fånglina. För att den skall kunna användas  krävs emellertid att ett tunnare snöre används. Någon plats för exempelvis en standard fallskärmslina  finns inte. 

Kniven hålls samman via två disanster utöver pivotskruven. Skruvskallarna är faktist T8or men riktigt usla om jag skall vara ärlig. Fästet för en mejsel är närmast obefintligt med ett välvt skruvhuvud och ett mycket grunt spår. Skruva inte isär den här kniven! Risken att du står där med runda skruvhuvuden är närmast hundraprocentig!

I det här utförandet har Revel ett titanhandtag

Längden på hela handtaget är 115 mm varav tillgängligt utrymme för fingrarna är ca 93 mm. Något som dock inte känns det minsta krampaktigt då fingerskyddet är mjukt format och det går att placera halva pekfingret över det utan problem. Baktill vidgar sig handtaget något för att förhindra att man halkar bakåt när man skär med kniven. 

Kniven är öppen i ryggen och där hittas även ett fäste för en mycket tunn fånglina

Titansidorna är designade så att det mönster som finns ger ett intryck av paneler. Det get lite fäste men det är främst formen och fördjupningen för pekfingret som bidrar till att hålla kvar kniven i handen. Det finns även några räfflor på basen av bladryggen för en tumme men de är mer av indexerande karaktär än att skänka något egentligt grepp. Något som jag övrigt är glad för då det på senare tid blivit allt mer diskussion kring hur dylika fördjupningar i knivblad påverkar den generella hållbarheten. 

Finishen överlag får godkänt då kanter och hörn är slipade och rundade som de skall vara. 

Revel har ett mycket bekvämt handtag. Det är lite för tunt för att vara extremt ergonomiskt

I hand är Revel bekväm på ett relativt neutralt sätt. Det är inget ergonmiskt muskelpaket men pekfingret hittar sin plats och det gör resten av handen också. Sedan gör den tämligen enkla formen att de båda grundgreppen, sabel- och hammarfattning fungerar utmärkt. 

Detsamma kan sägas om omvända grepp, inget som irriterar där heller. Rent generellt håller sig dessutom clipet ur vägen trots att det är av "deep ride"-typ. Det uppskattas då de ibland ger upphov till skav på grund av placeringen långt bak på handtaget. 

Öppning och lås

Det här är en lättöppnad kniv, förutsatt att man uppskattar Spydercos uppfinning bladhål, förstås. Alternativet är att öppna kniven med två händer vilket också går. 

Öppningsmetoden framgår tydligt av hålet i bladet

Bladhålet är lättåtkomligt och bekvämt att nyttja då det är fasat på ett sympatiskt vis. Mycket mer och det hade blivit halt. Det är alltid en avvägning. 

De fina keramiska kullagren gör att den här knivens blad har en tendens  att flyga ut snabbt. Särskilt gäller det om man använder sig av en s k "Spydie flick" med pekfingret på baksidan av kniven. 

Sedan är bladet rätt tungt beroende på form och tjocklek så motståndet (detent) kan övervinnas med en handledssnärt för den som vill provocera sin kniv och öppna den på det viset. 

En liten nackdel med den krispiga öppningen och det tunga bladet i kombination är att pivotskruven har en tendens att gänga upp sig. Du får antingen justera den med jämna mellanrum eller förse den med lite gänglåsning för att hålla den på plats. Efter ett tag blir annars öppningen för lätt och bladet börjar peka bort från låssidan. Med rätt justerad pivot är bladet annars centrerat.

Här hittas ett klassiskt ramlås med tillhörande låsarmsförstärkning och översträckningsskydd

Låset som hittas på den här kniven är ett ramlås med sedvanliga tillbehör. Med det avses en stålförstärkt spets på låsarmen och ett översträckningsskydd. 

Funktionen är mycket god med 100 procentig upplåsning och en låsarm som är lätt att nå. Låsarmen är därtill tämligen mjuk vilket gör låset lätt att släppa. Dock inte så lätt att det glider under felbelastning, det vill säga press eller lättare slag mot bladryggen. 

Något glapp upplever jag inte heller i bladet med låsarmen på plats. Det gäller dock så länge pivotskruven inte gängat upp sig förstås. 

Att bära

Revel är inte så dum att bära i en ficka. Med sina av mig uppvägda 114 gram är den inte avskräckande tung för sin storlek. Den är för övrigt drygt elva centimeter lång som nämnts ovan. Det skall paras med en höjd på som mest 35 mm och en tjocklek på endast strax över centimetern. 

Sammantaget en tunn och lätt kniv, särskilt om det ställ i relation med längden tillgänglig egg. 

Clipet är enkelt och av fjäderståstyp

Sidorna på handtaget är flata vilket inte heller det utgör något hinder när kniven förvaras i en ficka. Mönstret på titanet inverkar inte på hur kniven känns att dra eller stoppa undan. 

Så här ser Revel ut på plats i en ficka

Clipet på Revel är av enklaste slag och här märks det att det här egentligen är en "upphottad" version av en enklare modell. Det vill säga titanet i sig själv utgör en uppgraderad lyxdetalj.

Här hittas ett fjäderstålsclip direkt plockat från tillverkarens hylla och det hittas även på andra modeller. Det betyder dock inte att det är dåligt, bara att det inte är något extra och kanske ser lite tråkigt ut. Ett plus är  dock att dess blanka polerade finish går igen i bådeskruvar och blad.

Funktionen är bra med någon anmärkning. Rampen är liten men utgör i allmänhet inget problem även om jag som vanligt har synpunkter på spetsar som pekar utåt. De kan både skava och upplevs spetsiga om man slår handen i dem. Spänsten i clipet är god och utrymmet under, tja dugligt, inte mer. Särskilt inte som ett par millimeter i bakkant stulits av att clipet inte är försänkt i handtagssidan. Ytterligare en liten besparande åtgärd. Maskinbearbetningstid är pengar.  

Sammanfattningsvis

Revel är ännu en snygg och rekorderlig kniv från Ray Laconicos penna eller kanske CAD-program. Alla linjerna sitter som de skall och det som fick mig att välja den här kniven var det snygga bladet. Det är blankt, fint och är en clip point som ger Bowie-knivs vibbar. Helt rätt i mitt tycke. 

Sedan gillar jag renheten i Laconicos formspråk rent generellt. Några customknivar från honom vore inte ovälkommet men det är utom mina ekonomiska muskler. Istället får jag förlita mig på bland andra Artisan Cutlery. I allmänhet har jag kommit att gilla deras sätt att göra knivar vad gäller produktionskvalitet. Både finish och sammansättning brukar vara goda.

Det är den även här fast med några små undantag. 

Revel är en synmpatisk EDC-kniv då den är både praktisk och lätt att bära

Det handlar om några detaljer men de irriterar mig en smula måste medges. En sådan sak är kvalitén på skruvarna. De är helt enkelt inte bra i det här fallet. Skruvhuvuden är alldeles för grunda. Nog sagt om det. Fast nästa detalj handlar också om skruvar och det är själva pivotskruven. Problemet med att den gängar upp sig är förvisso tämligen lättåtgärdat men det förutsätter att du har Loc Tite eller liknande hemma. 

Sedan var det slipningen. En sabelslipning är vad den är men i det här utförandet anser jag att den är alldeles för tjock bakom eggen. Vilka uppgifter skalll utföras med en fällkniv som kräver att den är 0,6 mm tjock bakom eggen? Nu går det för all del också åtgärda genom att man slipar eller snarare helt reprofilerar om eggen. Det är för mycket jobb för min del.

Med det sagt skär inte Revel dåligt, bara inte så bra som den skulle kunna gjort Men någon risk att eggen flisar sig föreligger inte. Den håller dugligt och i kombination med ett tämligen bekvämtt handtag.

Något som  också kan diskuteras är titanets vara eller icke vara på den här specifika modellen. På den punkten väljer Artisan Cutlery att tillgodose olika smak och jag råkade välja metallhandtag. Modellen finns som sagt i andra material och mer exklusiva stål för den som föredrar det. 

Artisan Cutlery Revel är även stadig nog att fungera i skogen om du känner fördet

Men sammantaget kan det konstateras att de flesta intryck säger att Revel är resultatet av ytterligare ett lyckat samarbete mellan Artisan Cutlery och Ray Laconico. De har gjort det förut och jag tror att det kommer att hända igen. 

Revel är en både snygg och inte minst lättburen kniv och är en utmärkt plattform för den som söker en bra EDC-kniv. Valmöjligheter finns och de enklaste har ett riktpris från 45$ på hemsidan och det här utförandet hamnar kring 90$. 

Artisan Cutlery

Specifikation:

Längd utfälld: 205 mm

Längd hopfälld: 115 mm

Vikt: 114 g, vägd  av mig, uppgiven 113 g

Bladlängd: 90 mm

Godstjocklek: 3,2 mm

Bladstål: AR-RPM9

Handtag: Titan

Lås: Frame Lock

Producerad av: Artisan Cutlery, tillverkad i Kina

/ J - positiv

#knivesandbikes #aliaspostmortem #knivigtvarre 

New Knife - SRM Twin

This may very well be the best-looking knife SRM has ever made. At least for those who appreciate the dagger format, that is. It doesn't get much more streamlined than this in the world of folding knives.

The model is called Twin and has the model designation 251MB, with the addition of GB for this version, with a dark blade and laminated handle sides.

Twin is currently available in four versions. In addition to this version, the knife is available in another striking combination with a completely black blade and a white G10 handle. In addition, there is also multi-colored G10 and, not least, Micarta.

SRM 251MB-GB Twin

This knife is 178 mm long overall, and the handle is 101 mm long. It is a real lightweight, and both the materials contribute to this, but not least the thin, slender blade. The weight is only 70 g.

Twin boasts a single-sided, sharpened dagger blade that is 76 mm long and 2.5 mm thick. The steel used is N690. The dark surface is a titanium coating.

The handle sides, found on the outside of a heavily drilled-out steel frame, are made of a laminate with G10/carbon fibre in this case. More unique is the opening method, or at least one of them. You can open the knife using the lock, as it is a "cross bar lock" which in SRM's version is called Ambi Lock. A technique that they incidentally master better than most. If the locking bolt is pulled back, the blade swings freely and can thus be folded both out and in. Something that facilitates the smooth action is, of course, ceramic ball bearings.

A more streamlined knife is hard to find. Elegant was the word!

But the main method of opening the knife is the most hidden and one of the most effective "front flippers" I've come across. Just slide your thumb or index finger over the top of the handle, and the blade flies out.

The package is rounded off with a wire clip that works great.

As a dagger nut like me, this is a "no-brainer", a model I just had to have. Especially when it's as elegant as it is. A review will be coming soon.

SRM Knives

/ J - dagger up my existence

#knivesandbikes #knivigtvarre

Review Al Mar B-21 Folder

  

-  a flexible giant

The feeling of deja vu is strong in this case. For those who think they recognise this knife, they are not entirely wrong. I have previously presented and reviewed a knife from Al Mar that is very similar to this one. It is, of course, its close relative B-21 that I am talking about. With that in mind, it is not so far-fetched to see where the name of this knife comes from, as one of the few things that sets them apart is the ability to fold in half. Thus, this one is called the B-21 Folder.

Al Mar B-21 Folder

Behind the name "B-21" lies a thought, as it stands for Bowie for the 21st century, a modern interpretation of an old concept, in other words. It becomes especially modern in this case as it has been translated into a folding knife format. The man who designed this knife is, of course, Kirk Rexroat.

The relationship is not difficult to trace.

His name can also be found on several knives from Al Mar. It started early, back in 1997, when he made a custom knife called the "Havanna Clipper" for Gary Fadden, who was the owner of the company at the time. Since then, Rexroat has also designed knives such as the Back Up I, Back Up II and not least the Payara. The latter has been released in a new version that I reviewed.

Kirk Rexroat has also designed the folding version of the B-21

Short version: Al Mar B-21 Folder, a robust and versatile folding knife intended to replace a fixed blade knife

Blade

Like many other details, this blade is reminiscent of its fixed blade relative. It is based on a modified Bowie blade, which is basically a clip point. But here the description is somewhat more extensive. The Bowie part consists mainly of the boldly cut tip, but its characteristic false edge.

The modification is found in the clear bend found in the blade spine, a detail that is also reinforced by the thumb ramp that leads to it. They create more ways to grip the knife.

The modified Bowie blade is also found in the folding knife version of the B-21.

The fact that this is a relatively large folding knife is reflected in the dimensions of the blade. It is 95 mm long and 35 mm high. The thickness is 3.3 mm, which does not feel excessive considering the knife's intended use as a "tactical"/outdoor knife. But by all means, it would have been durable enough with a 3 mm blade as well. What sometimes seems to be overlooked is that the height of the blade, of course, contributes to the strength in everything except when you use your knife as a crowbar.

One thing that contributes to the robust impression is the choice of steel. D2 is not an extraordinary material, and sometimes I don't like it, as I have had problems with corrosion with several knives. Sometimes D2 is considered "semi-stainless", but I don't know if I agree with that.

But in this case, the choice feels correct as it is a steel that can withstand a lot of abuse. It doesn't chip easily, and it can be made really sharp. Given that the hardening is good, it also keeps its sharpness for a long time. The factory edge on the B-21 was also very good, sharp and relatively even. 

The steel has been given a satin finish, the shiny surface of which helps to keep rust away. The marking is otherwise quite discreet with Al Mar's new logo, the one without the red in it, on one side and the model name, designer and country of manufacture on the other side. A lot of information, but in a small format.

The steel used is D2

Then they have chosen a fairly steep edge and a blade that certainly has a high flat (not full) grind. The primary edge is 25 mm high. In addition, the knife is a full 0.7 mm thick behind the edge to be extra durable.

Of course, this affects how the knife works in different materials. It is clear when you use the knife that it is more intended as an outdoor and perhaps hunting knife than for typical EDC tasks. It is not the world's best cardboard killer, but it was not intended as such either. At the same time, it should not be exaggerated; it is all about nuances. A sharp edge and a sturdy handle mean that it is just work, and also longer than most, given the good ergonomics. So it is possible to shred large amounts of cardboard, just not as easily as with the best knives for the purpose. 

It works significantly better in meat. I'm not a hunter, but I've tested it on mixed pig parts, read chops and loins to get an idea.

Wood in different conditions, fresh and dry, as well as rope of different types, are other things that this type of knife has to handle well, and it does. It's among the most common things you come into contact with if you're outdoors in any form.

Then the tip is a joy. Sharp enough for small jobs and strong enough not to break. The geometry also means that it penetrates, for example, thicker plastic in an excellent way. Small jobs I often perform are minor "surgical procedures" on my own person in the form of picking metal chips out of my hands. As a knife thrower, this is a frequent occurrence. This tip also works for that.

Handle

The eye-catching blade is matched by the handle. Here we have a bold, blue anodised frame and a generally sculptural appearance.

This, in turn, results in a handle with many details worth noting. We can start by stating that it has both substantial protection against slipping forward and backwards. It is noticeable that Rexroat was looking for a handle that worked for various tasks. At the front, a finger guard is found while the upper part forms a thumb ramp. Both braces and a waist belt, in other words. In the same way, the handle swells at the back into a "duckbill" that prevents the user from slipping backwards when cutting.

The handle is both spacious and flexible

The sculptural look comes from the G10 side panels that are heavily shaped. At most, they are around 4.5 mm thick. But they are both arched and thinned out at the front. The entire knife is 15 mm thick at most and only 6.5 mm at least, which is almost unique. But there is a subtlety to it that I will return to.

The length of the entire handle when the knife is folded is 130 mm, and the usable space for the fingers is 90 mm. Although it is true with modification depending on how many ways there are to vary the grip. Then the rear part of the handle is designed so that if an extra centimetre is needed, if you wear thicker gloves, for example, that also works.

The back shows the blue anodised frame and a steel back spacer.

The construction is somewhat special compared to most folding knives for a couple of reasons. One thing that stands out is, of course, the blue colour used as an accent colour. But what is more unique is how much of the frame is in contact with the blade around the pivot screw. This gives a significantly stiffer and more durable folding knife laterally. A detail that is often overlooked when making more stable folding knives. Most often, manufacturers only talk about lock strength.

Speaking of strength, it can be added that the frame is not lightened in any way. One of the things that, together with the dimensions, the steel back spacer and the many screws, of course, contributes to the high weight. By many screws, I mean that the sides are attached with three small T6 screws per side, but these are not the ones that hold the frame together. There are three more equally small screws per side in addition to the pivot screw for that. The pivot is a solid T10. But that means that no fewer than thirteen screws can be found in this knife, even though it lacks a clip.

The balance point is found just behind the finger guard. The B-21 is really comfortable in all common grips...

The shape described above makes for a very versatile handle. It naturally fits perfectly in a hammer grip, which would be strange otherwise, since it is a sturdy folding knife, and that is the grip that provides the most power.

The B-21 Folder can then be held in two variations of a sabre grip, both with the thumb on the thumb ramp but also with the index finger just behind the edge on the flat part of the blade, and with the thumb in the recess on the blade spine. This allows you to get significantly closer to what is being cut, which is excellent for detail work.

...and a few more. In fact, this handle works in all different grips

The shape described above makes for a very versatile handle. It naturally fits perfectly in a hammer grip, which would be strange otherwise, since it is a sturdy folding knife, and that is the grip that provides the most power.

The B-21 Folder can then be held in two variations of a sabre grip, both with the thumb on the thumb ramp but also with the index finger just behind the edge on the flat part of the blade, and with the thumb in the recess on the blade spine. This allows you to get significantly closer to what is being cut, which is excellent for detail work.

In addition to all the other possibilities, this knife is also excellent for holding in a reverse grip. Not least, the flat back end of the handle makes it easier to hold the knife with the edge down/forward. If you pull towards you in a reverse grip with the blade up, both the thickness and length of the handle are of great help.

Opening and Lock

The B-21 Folder opens with thumb studs, which is quite unusual, only in one way, and that is slowly and stylishly. That is, the knife does not have any ball bearings, and the blade cannot therefore be flicked out. It is completely in line with the area of ​​use. No bearings that can accumulate gravel and dirt unnecessarily.

You can open the knife with two hands if you feel like it, but only a little of the blade sticks out, so it is a manoeuvre that is not entirely easy.

The thumb studs do what they're supposed to, easy to access and with good leverage.

The thumb studs are quite large in size, which makes them easy on the thumb. To increase the grip, they have a pattern on the top. They are correctly positioned to provide leverage and make the opening smooth. They are also not so high that they stick out too much. Something less important on a knife that is not carried with a clip in a pocket. But you still don't want protruding parts that can get caught on things.

This is a heavy-duty liner lock with a lock bar that is almost hidden.

Given that the frame is around 1.5 mm thick, the liner lock found on this knife is also sturdy. It is very well made and has never failed to lock up.

When the lock bar is in place, it holds the blade very stable. There is no play in any direction, not even if the blade is provoked. The only peculiarity is that the lock is quite difficult to release. There is a recess to facilitate access, but it is cramped, and the lock bar has no pattern to prevent your finger from slipping off.

Now I think the design is like that on purpose. I have come across a similar idea in a knife from Spyderco, namely the Bradley Folder 2. What it is about is that you "hide" the lock bar so that you absolutely cannot access it, even if you perform twisting movements with the knife. Something that is otherwise a theoretical risk with liner locks. 

To Carry

Then there was the elephant in the room. Or maybe not, because it's not hidden. Just an elephant then. The B-21 Folder is built to replace a fixed-blade knife, and of course, it shows. As previously mentioned, it is thirteen centimetres long and one and a half centimetres thick. Yes, and then it's over four centimetres high too. If you sum it all up, you get a lot of volume.

But it's still the weight that stands out. This knife weighs in at 195 grams. A heavyweight for a folding knife.

A sturdy leather sheath is included to carry the knife in. Here I have wet-formed the leather for a better fit.

For these reasons, it was sensible not to equip the B-21 Folder with a clip. It would have been too bulky in the pocket. Of course, the trade-off is better ergonomics with protruding metal parts out of the way.

Instead, this knife comes with a classic "pancake" leather sheath. It is made of strong, light leather and is well-stitched. On one side is a classic checkered pattern, and on the other is the Al Mars logo embossed.

This is what the sheath looks like when it's just unpacked from the box

Dock rekommenderar jag att du våtformar fodralet efter kniven. Att naturligt slita in det till en bra passform lär ta evigheter med den läderkvaliteten. Fodralet har hällor för bälten upp till 45 mm bredd. 

To Conclude

Since I was very fond of the fixed blade variant, I felt like I had to see if I appreciated the folding version of the knife as much. And I do, maybe. I have to admit that I am a little ambivalent. Everything that is the strength of the knife is also its Achilles heel. Let me explain!

After all, the Al Mar B-21 Folder is intended to replace a fixed blade knife, something that both the dimensions and the belt sheath tell us about. We have a folding knife with a sturdy blade but an even sturdier and more versatile handle. The materials are chosen to be durable, and this is also reflected in the construction. This is evident, among other things, in the fact that the strong steel frame has a large contact surface against the blade for increased lateral strength and that the frame is not lightened.

B-21 Folder and a coffee in the spring sun

Functionally, it is a very good knife. The blade shape is usable for most things with a good tip, just enough belly and a bit of a straight edge to work with. There are not many tasks that cannot be done with that equipment.

Then, as I said, you have a handle that allows for everything from a very powerful hammer grip to a very delicate pinch grip. It is a bit of an art to achieve that, something that Rexroat has succeeded in.

Overall, it is therefore a very good handle. I have one small complaint, however, and that is the implementation itself. The corners at the recess that facilitate access to the lock bar are too sharp, and the same can be said about the inside of the frame. Something that I chose to round off myself.

But all these advantages come with a price. The B-21 Folder is naturally a large and heavy knife. It is a folding knife that is not a pocket knife. Something that I said explains the included sheath. Then it can be added that when using a sturdier winter jacket, I still carried it at the bottom of a pocket. Otherwise, it mostly resides in bags. The way of carrying it is a bit polarising; however, not everyone likes belt sheaths for folding knives.

If you are one of those who do not see this as an obstacle, this is an excellent choice from Al Mar.

Al Mar B-21 Folder in all weather. Here, during a hike last fall

The B-21 Folder is a very good knife. Versatile and also very well built. It is made in Taiwan, by the way. So if you are looking for a robust knife with a focus on hunting and outdoor activities in a folding format, this is a very good candidate.

Al Mar

Specifications:

Length Overall: 226 mm

Length Closed: 130 mm

Weight: 195 g

Blade Length: 95 mm

Blade Thickness: 3,3 mm

Blade Steel: D2

Handle: G10

Lock: Liner lock

Produced by: Al Mar, made in Taiwan

/ J - looking for heavy hitters

#knivesandbikes #aliaspostmortem #knivigtvarre